If you have this issue with your Maytag, Samsung, LG, Kitchenaid or Frigidaire fridge probably this will apply to any fridge manufacturer been not cooling, you need to check couple things to fully understand the problem. There is a big probability that the compressor is lost efficiency in other words is dead or there is a restriction in freon sealed system usually on the dryer filter side.

In this case, you need to call Appliance Repair Technician to fix this issue. You will not be able to fix it by yourself in most cases. Now, this issue when not cooling enough is a little bit advanced and requires the right knowledge and tools to track it down and fix it.

Before you get the big repair tools and begin tearing your beloved fridge apart, start by double-checking the controls. This happens mostly if you have kids around who may unknowingly or purposefully dial in the incorrect cooling settings.

Why is Fridge Compressor Running But Not Cooling?

You can always dial up the control temperature one number higher if the beverages are not getting as cold as you like. Always unplug the fridge, then transfer your items to another fridge to keep them preserved while you work on the faulty fridge. Remember to keep a few towels nearby to soak up water that leaks onto the floor as you thaw away the frost from the evaporator coils.

But remember, thawing it for longer than 24 hours ensures all the frost from the frozen sections is completely melted. After melting all frost away, plug the fridge and test it, if it works, then the likely cause of the frozen evaporator coils is a faulty defrost timer, a faulty defrost thermostat or a bad defrost heater.

These parts may be replaced easily once you call in a pro to troubleshoot exactly which part is defective. Or if you want to speed up the defrosting process, you will need a steamer and you can defrost evaporator coils in 15 minutes. If your fridge is not cooling and this is accompanied by increased vibration and squealing noise whenever you open your fridge, then the likely cause of both problems is a faulty evaporator fan.

The evaporator fan is located inside the freezer compartment, near the coils, and covered by a fan cover. To verify this, open the fridge door and feel using your hand, at the back of the fridge, if the fan is blowing. If the temperature at the back of the compartment is the same level as that of the room, then the fan is not working. Replacing the evaporator fan should fix the issue. You can get fan HERE. The compressor and condenser fan are located behind a rear access panel at the back of the fridge and usually come on if the thermostat demands more cooling.

Condenser fan providing proper heat exchange for the condenser coils. To verify the faulty condenser fan problem, pull your fridge away from the wall, unplug it then proceed to remove the rear access panel near the bottom. Also, if the fan is noisy, replacing it will save you from headaches as very loud fridges can interfere with conversations, etc.

If the compressor cools and starts to run, then what interfered with its operation initially was a faulty condenser fan. The start relay is usually mounted to the compressor; it helps kickstart the compressor during the cooling cycle. If the start relay is faulty, you may hear clicking as the compressor turns on and off intermittently. A fridge condenser is just like a radiator; it must stay kept clean to dissipate heat from the fridge.

In the case of dirty condenser coils, the refrigerator will never be able to cool down to the temperatures you like. A dirty condenser coil may even make the thermostat to cut it from the power supply if it begins to overheat. Also, as the compressor overheats due to dirty condenser coils, it turns on and off, causing clicking sounds to come from the back of the fridge every minutes. To check the dirty condenser coil issue, unplug the fridge, open the rear access panel at the bottom of the refrigerator and visually inspect the coils.

If the condenser coils are dirty, you can vacuum the dirt away. The thermistor is a sensor connected to the fridge control board and monitors air temperature inside the fridge. If you suspect a faulty thermistor, call in the fridge repair expert as this is a bit technical problem.Your freezer is cold but refrigerator is warm?

This can be a very big problem. When the evaporator coils frost over, air can not easily pass through and get cold. First manually defrost the coils by applying hot air to them with a hair dryer. Afterwards, let your fridge continue to run normally.

If the coils frost over again, you should check your defrost heater assembly to make sure it is working properly. If the defrost thermostat is the culprit, you will need to change it. Check out the video below to find out how. Another potential problem is the defrost timer is not functioning properly.

The when the defrost timer advances, it provides power to the heating element. As it continues to advance, it cuts the power to the heating element and provides power to the cooling element. If the timer gets stuck, it can stuck in one of the two modes. The defrost timer can normally be found in the temperature control section inside your refrigerator. To test if the motor works, locate the screw and turn it clockwise to advance it to the next position.

If it is was in cooling mode before, it will now be in defrost mode. Wait around 30 minutes and listen for the compressor to see if it has gone back into cooling. This procedure is just opposite if it was in defrost mode first and you switched it to cooling. If the timer failed to advance, you should replace the whole timer unit. If it advanced, you can continue on and check the timer electrically. You will need to test the defrost timer for continuity. If it fails, you might need to replace it.

Check out this handy guide below to find out how to replace your evaporator fan.If food in your fridge is slowly beginning to spoil, you might notice the recent warm-up of your appliance is accompanied by an occasional clicking noise. The bad news is that your refrigerator is in immediate need of repairs, and the good news is that you can diagnose it pretty easily. There are a limited number of things that would cause both clicking and a stoppage or decrease in cooling.

You may be able to repair it without calling a professional and spending unnecessary money. One reason your refrigerator would click would be a compressor overload caused by a dirty condenser coil. The clicking sound is the compressor shutting itself down on the overload. The condenser coil is located near the compressor, either on the rear or bottom of the refrigerator. This is the tubing through which the refrigerant flows after compression to dissipate the heat and prepare for expansion and cooling.

If the refrigerator is cooling poorly but still seems to retain some cold air, then this is likely the problem.

Because it is located in a rarely cleaned area on the outside of the refrigerator, it accumulates considerable dust and other substances, such as kitchen grease. The coil needs to be cleaned at least once per year to prevent cooling problems and compressor overload. Plumbing stores sell a condenser brush specially designed to clean the coils.

Remember that when you clean the condenser coil, you should unplug the refrigerator to prevent electric shock. If your refrigerator has stopped cooling entirely and you hear a clicking sound every two to five minutes, then your compressor is not turning on. The start relay is a device that starts up the compressor so that it can begin the cooling cycle by compressing the refrigerant gas in the appliance.

This small device is located inside the same compartment as the compressor and usually plugs right into the side of it. If the start relay is failing, it will click as if it were trying to do its job, but the compressor will not come on.

Within a short time it will try again without success. To confirm that the start relay is the problem with your fridge, disconnect the power from the refrigerator and pull the start relay out from its socket on the side of the compressor. Give it a shake. If it rattles, the start relay is faulty and needs to be replaced.A refrigerator not staying cold enough is a hassle, as you are at risk of spoiling the foods inside.

Most often, this problem is caused by something easy to fix. The door gaskets in a refrigerator ensure a sealed closure every time you shut the door. Torn or loose gaskets on the door can result in leaking cold air, and as a result, the refrigerator is left warm. Repetitive and frequent opening and closing of the refrigerator is also a possible cause because the warm air from outside replaces the cold air in the refrigerator every time you open it. Dirty condenser coils can result in improper functioning of the fridge.

Refrigerator Not Cold Enough: 8 Possible Causes

These coils are located on the back or the underside. If you find this to be the cause of the problem, unplug the refrigerator before you attempt any cleaning, then pass the vacuum cleaner over the coil area. If the frost-free feature fails, it will cause a buildup of frost around the evaporator coils in the freezer.

This causes a malfunctioning of the evaporator fan that blows cold air around. The fan can also be damaged if it hits the frost. You can tell when a fan blade gets damaged by the loud noise coming from the now unbalanced fan.

A faulty thermostat can lead to a refrigerator that is not maintaining the desired coldness. Check for this problem and also ensure that the temperature is set to the correct level.

A refrigerator that is loaded with too many food items can fail to maintain an adequate level of coolness across all the items kept in it. The surface items tend to be colder, and the items underneath do not become as cold. A refrigerator that has very few items in it can also fail to function efficiently.

Try to ensure that your refrigerator has enough food in it at all times, but is not so loaded that the air flow gets constricted. The vents between the freezer and refrigerating section permit the flow of cold air from the freezer across to the refrigerator.

These vents should never get clogged with ice, but if for some reason it does, the impaired air circulation will keep the refrigerator section from cooling down. If this is the case, you can unplug the refrigerator, wait for the ice to melt or remove the impairement, then plug it back in. The door switch is found around the perimeter of the refrigerator door opening, where it can activate this switch.

It turns off the light in the refrigerator and resumes cooling action when you close the door. If this switch is not functioning properly, the refrigerator will not resume cooling as normal and may also be affected by the heat of the interior light not switching off.

A refrigerant leak is very unlikely but can obviously cause malfunctioning of your refrigerator. If you suspect this to be the cause, contact a service technician. We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here. Toggle navigation subscribe.Are you finding your refrigerator running warm?

After all, the last thing you need is food spoilage and money down the drain. The good news is, when your Whirlpool fridge is not cooling enough, a few DIY steps will often get things moving in the right direction again. Dirty condenser coils are the most common cause for a Whirlpool refrigerator not cooling. Condenser coils dissipate heat as the refrigerant passes through them.

You may have even noticed your refrigerator is noisywhich can be due to your fridge working harder to maintain a proper temperature. The second most common cause for a Whirlpool refrigerator not cool is a defective door seal. The door seal ensures the cold air inside the refrigerator is locked inside rather than leaking into your kitchen.

why is my whirlpool fridge not cooling

Check the door seal for damage, gaps, or other defects. Is your Whirlpool refrigerator not cooling but freezer is working? Check your temperature setting. Possible Cause 1: Dirty Condenser Coils Dirty condenser coils are the most common cause for a Whirlpool refrigerator not cooling. Clean the Condenser Coils Pull fridge away from the wall — allows better access to the back and underneath of unit. The coils are snake-like in shape and often located under the refrigerator.

You may also have a toe guard at the bottom front of the fridge that can be removed for better cleaning.

why is my whirlpool fridge not cooling

Vacuum — use a narrow hose attachment to vacuum all the coils and external hardware on the refrigerator. Use a Dryer Brush — scrub the coils with a dry brush to remove stubborn debris. Vacuum — give one more vacuum to remove all remaining dirt.

Photo from Green Living. Image from The Family Handyman. Image from Gina Valley. Easy Guide to Ice Maker Maintenance. Refrigerator is Noisy.A Whirlpool fridge not cooling means a shorter preservation life for all your refrigerated food than you're expecting. Before your food begins to spoil, follow a short troubleshooting list to see if you can take care of the problem first without having to call a refrigerator technician.

You may be pleasantly surprised to find that some solutions are easy to diagnose and resolve, even if you're typically not a fix-it guy or gal. If your Whirlpool refrigerator is newly installed, cooling is not instantaneous; it takes a little while for it to cool completely. Allow 24 hours from the time you connect power to your new fridge and turn on the cooling feature before you put food inside.

If you add food before this initial cooling period, it may spoil. Resist the urge to adjust the cool settings lower than the recommended temperature in an effort to reduce the initial cooling period of 24 hours; Whirlpool notes that doing this will not cool your fridge any faster during the initial cooling period.

Whirlpool Gold Refrigerator Diagnostic And Repair - Fridge Not Cooling

Whirlpool presets the refrigerator cooling control at the factory to 37 degrees F 0 degrees F for the freezer. And for the most part, these are also the temperatures at which you want to maintain your fridge's settings.

But if you do need to adjust the temperature to a cooler setting, do this by setting the control only 1 degree F lower at a time.

After lowering by 1 degree F, wait 24 hours to see if this incremental change sufficiently cools your food.

If not, lower it by 1 more degree F and wait another 24 hours, repeating this procedure if necessary. A common solution for your fridge and freezer not cooling requires a little housekeeping. As refrigerant moves through a fridge's condenser coil, the coil removes excess heat, which maintains the efficiency of the coil as it keeps your refrigerator cool.

But because this coil typically is located at the bottom of a refrigerator, it can become clogged with dirt, dust and pet hair. If the coil becomes clogged with this debris, it loses its ability to remove excess heat and the refrigerator has to work harder just to keep food cool.

Before you attempt to clean your refrigerator's condenser coil, unplug your fridge or turn off the circuit breaker that supplies power to it. Consult your user manual for the exact location of the condenser coil and the removal steps for the metal grille or kick plate that covers the coil. Generally, you'll remove this grille by pushing down on it and snapping it off or by removing screws that hold it in place. With the grille removed to expose the condenser coil and your fridge unplugged, use the hose end of a vacuum cleaner to suction all the debris from the coil.

Replace the grille, restore power to your fridge and wait 24 hours before checking to see if the food inside is cool.

My Fridge Is Clicking and Not Cooling

For a fridge compressor running but not cooling, the problem can lie with the compressor or with the components that help it work, such as the start relay and start capacitor.

The compressor is the pump that circulates refrigerant through the condenser coil. The start relay is what signals the compressor to run, and the start capacitor boosts power to the compressor when it starts.

Diagnosing, repairing or replacing these components are tasks best left to licensed refrigerator technicians. Her writing expertise covers diverse industries, including horticulture, home maintenance and DIY projects, banking, finance, law and tax. Blackstone has written more than 2, published works for newspapers, magazines, online publications and individual clients. Hunker may earn compensation through affiliate links in this story.

It might be easy to fix your refrigerator by yourself. Recommended Refrigerator Temperature Setting. Victoria Lee Blackstone. Connect on LinkedIn. Show Comments.If you recently had a power outage, your refrigerator may need to be manually turned back on. Your refrigerator also could have been accidentally turned off during a routine cleaning.

To see how to turn your refrigerator on and off, refer to its use and care guide. Check to make sure the outlet is working by plugging in a lamp or other small appliance. First make sure the controls are turned on. Then check the setting. Most controls are preset to the mid setting, which should be correct for normal household use. If you need to adjust the temperature, wait 24 hours after adjusting to see if the temperature has changed.

Adjusting to a higher setting lowers the temperature in the refrigerator, and adjusting to a lower setting raises the temperature. This mode is used on some store display models. You may need a professional repair. Or, if your refrigerator is more than 10 years old, it might be time for a replacement.

Amana has great refrigerators at a great value — check out the latest. By closing this message, you consent to our cookies on this device in accordance with our Privacy Notice unless you have disabled them.

Heating and AC. Wall Ovens. Refrigerators Freezers. Washers Dryers. Refrigerator Not Cooling? Refrigerator is not turned on If you recently had a power outage, your refrigerator may need to be manually turned back on. Controls are off or set incorrectly First make sure the controls are turned on. Still not cooling? Comparing 0 Items.

Link Example. Email me a transcript of this chat.

why is my whirlpool fridge not cooling

thoughts on “Why is my whirlpool fridge not cooling

Leave a Reply

Leave a Reply

Your email address will not be published. Required fields are marked *